Barstool Racer Supply

[Mike Bean]

:hot:
Visit our online store, barstoolracersupply.com (http://barstoolracersupply.com/). We carry the specific parts required to build a barstool racer, and take all the guess work out of which parts to buy.

BarFlyRacers.com

Finding your parts is fast and easy. Our parts have detailed descriptions, photos and installation advice for the barstool racer builder.

[nsanesider]

I was wondering if you have the classic frame in Stock ready for shipping? Also A shipping figure to Savannah ,GA. (31406)Also was wondering what the prices are for you to weld up the frame and ship it to the same area code?

[Mike Bean]

I was wondering if you have the classic frame in Stock ready for shipping? Also A shipping figure to Savannah ,GA. (31406)Also was wondering what the prices are for you to weld up the frame and ship it to the same area code?

nanesider,

We just finished welding up a Classic Cruiser frame this afternoon and it is ready to go. I can sell it to you for $180.00 plus $60.00 shipping to your location. The frame will be shipped UPS.

Let me know ASAP if you want it. We were going to put it on eBay tonight. Also if you need any other parts please let me know and I can send them with.

Mike Bean

[nsanesider]

I'll take it! Do you take Paypal? if so, I need a day or two to get funds into my paypal (Toyaccouant).Also, Is this bare metal? Do you offer it in any color's? Does this come with a detailed parts list needed to complete this barstool? Any help is appericated,I have many spare racing go kart parts,Are these interchangable? Thanks Alot, Jay

[Mike Bean]

I'll take it! Do you take Paypal? if so, I need a day or two to get funds into my paypal (Toyaccouant).Also, Is this bare metal? Do you offer it in any color's? Does this come with a detailed parts list needed to complete this barstool? Any help is appericated,I have many spare racing go kart parts,Are these interchangable? Thanks Alot, Jay

nsanesider,

We do accept Paypal. Let me know when you have the funds ready and I can send you an invoice via Paypal for the total.

Right now the frame is bare metal. We can paint it any color you want. If we paint the frame it will delay shipping by about a week and there will be an additional cost for the paint and time of $40.00. When we paint the frame we use a paint gun so you will get a very nice paint job when finished.

Quick note, if we do paint it, I would suggest to add the rear brake assembly before painting. We can supply the brake caliper and brake disc for an additional cost. We usually do not add the braking assembly because some people prefer to add their own.

We will send you a set of our plans for building the Classic Cruiser and that will have all the parts needed to complete. Barstool Racers a primarily built from go-kart parts, so depending on what you have, you might be able to use some.

Let me ask you, do you have access to a welder? The reason I am asking is if you want to use a stool different than mine I can leave the barstool leg supports off so you can position them to your stool.

Mike Bean

[sniffles]

how many frames and complete barstool racers have you sold? oh and how long did it take to design the frame. not how long it took to actually make it but how long did it take you to think of the design? :blob_red:

[nsanesider]

Mike, Yes, I have access to a welder. On the painting side of it,I think I'll try and tackle that part for now. I'll just wait and see what all parts I can scavage off of my Kart. Funds will be ready tomorrow if I can make it to bank before 2pm.Thanks and look forward to the transaction!

[moto1fast]

Hello, Mike your rear weld on bearing brackets that are for 1" bearings can these brackets also be used on 1 1/4" bearings? Also will the bearing flange plates for the 1 1/4" line up with the bracket holes? Thanks

[nsanesider]

Good question on the 1 1/4 axle bearings hanger. I think thats what my kart has on it.

[Mike Bean]

Hello, Mike your rear weld on bearing brackets that are for 1" bearings can these brackets also be used on 1 1/4" bearings? Also will the bearing flange plates for the 1 1/4" line up with the bracket holes? Thanks

There are actually two different hanges for the 1" and 1 1/4" bearings.

Hey Stool-Sample, I am sure you can answer this question?


:hot:

[nsanesider]

Hey Mr.Bean, Shoot me a PM on what it would cost me to have you just go ahead and make it a roller, minus the tires and wheels. tie rods,spindles,rear axle and brakes.I was gonna chop up my old race kart,just trying to figure out my best options? Basicly I just wanna assemble the basics,powerplant and tires.

[Mike Bean]

how many frames and complete barstool racers have you sold? oh and how long did it take to design the frame. not how long it took to actually make it but how long did it take you to think of the design? :blob_red:

Sniffles,
We have sold quite a few frame kits. Do to the time it takes to assemble and weld the frames we do not always sell them complete. On this new design, we created the frame so it can be shipped via UPS fully welded.

As for the time to design...well we did some drawings on paper and then started to build it. I really do not know how long it took to come up with the design because I had an idea on paper and then finished it as I built it. I ended up adding the front nose as the last part after the frame was fully built.

Mike Bean