Where to find hubs for douglas rims.

[xtman]

I bought these wheels and tires off a friend of mine, the frons whent on find but the rears my hubs dont fit! I took it to a gokart shop today adn he said that i need certain hubs for douglas rims. He recommended a place called extreme wagonz? But i cant find them. Anybody know of a place?

[hellbentrodder]

I have seen that name on E-bay....but can't find a site. He make frames for Radio Flyer wagons.

[Garman351]

I have seen that name on E-bay....but can't find a site. He make frames for Radio Flyer wagons.

BMI cart supply has just about anything you could ever look for.

Garman351

[Woodchuckscustoms.com]

Check out WOODCHUCKSCUSTOMS.COM for BSR Parts:thumb:

[Mike Bean]

Don't forget to check out BarstoolRacerSupply.com (http://barstoolracersupply.com)!
Your #1 Online Source for Barstool Racer Parts!
:thumb:

[Mike Bean]

I bought these wheels and tires off a friend of mine, the frons whent on find but the rears my hubs dont fit! I took it to a gokart shop today adn he said that i need certain hubs for douglas rims. He recommended a place called extreme wagonz? But i cant find them. Anybody know of a place?

Xtman,

Click the link below for the hubs for the Douglas Rims:
http://barstoolracersupply.com/product_info.php?products_id=94 (http://barstoolracersupply.com/product_info.php?products_id=94) (font and rear kit)
http://barstoolracersupply.com/product_info.php?cPath=25&products_id=92 (http://barstoolracersupply.com/product_info.php?cPath=25&products_id=92) (rear hubs only)

We also have the hubs in 1-1/4 if needed.

[xtman]

I dont get it. That's the hub i ordered and it doent fit.

[Mike Bean]

I dont get it. That's the hub i ordered and it doent fit.

Are you sure you have an american bolt pattern hub?

American bolt pattern hubs will fit most wheels ex. Douglass, VanK, Circle, Burris etc...

Do the bolt holes not line up or are the bolts to big for the rim?

Mike

[xtman]

I think i worded it wrong, adn im really sorry. The bolt pattern is correct. The problem i have is that on the end of the hub, the part that slips into the wheel is too large. Not the tapered side, the other side.

On a side not i ended up jurying up my rear wheels today and i took my BSR to a car show today. I couldnt believe how many people wanted it! Once i finish this one i think i might have to start selling rollers.....

[voodoo_stepchild]

I think i worded it wrong, adn im really sorry. The bolt pattern is correct. The problem i have is that on the end of the hub, the part that slips into the wheel is too large. Not the tapered side, the other side.

On a side not i ended up jurying up my rear wheels today and i took my BSR to a car show today. I couldnt believe how many people wanted it! Once i finish this one i think i might have to start selling rollers.....


Douglas runs a smaller bore on all there wheels. Might have to machine the lip donbw just a bit on your hub. OR!!!! you have a severly egged hole in the center of your wheels

Voodoo

[xtman]

YEP! you were right. I figured this out almost a month ago. I bought these rims off a kid that races go karts. So i had to get special hubs made for a 40mm axle, then i had to machine a 40mm spacer with a 1in. hole in it so it slid over my axle.