Budget stool

[upsracer]

Here are some pics of my $125.oo stool.1554

1555

[Redrooster]

Hi... can't see anything

[upsracer]

Thanks, but the pics come right up when I look at post. I don't get it.

[largedoublea]

Not bad for 125 bucks. Did you paint it purple to match the Harley??:thumb:

[upsracer]

Not bad for 125 bucks. Did you paint it purple to match the Harley??:thumb:Yep, built that too,(ya right)color is closer than it looks. Thanks

[Redrooster]

I don't know what happened the first time the pictures did not come up but now I can see them... Good job I think it looks good... how fast will it go and what kind of motor does it have on it?

[Redrooster]

Hey...how about some close up detail pictures...Thanks

[upsracer]

Hey...how about some close up detail pictures...ThanksI'll have some more pics tomorrow. I put a 12 volt hydraulic motor on it a neighbor gave me. Slow on take off but will get up to about 20, plenty fast enough for the hand cart tires.

[upsracer]

1565

1566Here are a few more pics, this was my 1st stool just used mostly stuff I had around the house. I made all of the steering parts to keep down cost. I may make a gas one next and buy some of the parts. My back axle is a 1 inch rod with stainless bolts welded on. Steering is 5/8 bolts and 3 in channel welded.

[Matty_C]

i cant see the pics:(

[upsracer]

i cant see the pics:(Works when I look, try again.:wave:

[Redrooster]

Hi upsracer... Thanks for the extra pictures... I can't quite see close enough to see how you hooked up the electrical for the motor and are you running some kind of speed controller? could you take one more picture closer up to see alittle more detail in the motor area? Also how did you lock your back wheels to turn with the axel so they would'nt spin with the bearings... Thanks again... great job...

[upsracer]

Hi upsracer... Thanks for the extra pictures... I can't quite see close enough to see how you hooked up the electrical for the motor and are you running some kind of speed controller? could you take one more picture closer up to see alittle more detail in the motor area? Also how did you lock your back wheels to turn with the axel so they would'nt spin with the bearings... Thanks again... great job...Thanks for the interest Red, couldn't use a speed controller w/12volt. There is a battery cut off switch, and a ford solenoid under the motor, to the rt is a on off switch hooked to a throttle pedal that also runs a belt tensioner. Just put washers on either side of wheel and tightened with nut and lock nut.:blob_red:

[Turbo_Stoolie]

I dont see anything...lol.

[largedoublea]

can't see anything ????

[upsracer]

I dont see anything...lol.Check with moderator, the pics are there when i sign on and look.

[upsracer]

can't see anything ????Check with moderator, pics are there when I log on and look.:dizzy:

[upsracer]

Did I screw up on posting my pics or are they there?

[b.raven70]

I dont see any...Is it maybe our the internet browser we're using?

[upsracer]

OK, I give up, I'll crawl back in my hole now.:hammer:

[Mike Bean]

OK, I give up, I'll crawl back in my hole now.:hammer:

The pics are showing up fine. It may be some older browsers or a browser other than AOL, IE, Netscape.

If you are having problems viewing the photos, try using the IE browser 5.0 or newer. Also, when attaching photos if you just attach them so they have to be clicked, then everyone can see. I think there is some new technology in the forum when you attach multiple photos and show them all at the same time, some browsers are not compatible yet...

Mike Bean...The Big Cheese... :laughing:

[Redrooster]

Hi... Most of the time the pictures come up for me... I am using netscape... a few times they haven't...

[moto1fast]

Hello, I see them fine! Just not enough of them! LOL:blue_blob:

[upsracer]

Thanks guys, now I still feel loved.:wave: